大网数据广告活动
服务器运维问答

Linux: bridges, VLANs and RSTP

· 52CE 我爱测

I tried to figure out how to setup RSTP on Linux with VLANs and bridges involved and now am completely confused. I am trying to bridge three interfaces, two of which are supposed to act as trunk (hdlc0 and hdlc1) and one is suppo…

问题原文

原帖链接 · grindelwaldus · CC BY-SA 3.0

I tried to figure out how to setup RSTP on Linux with VLANs and bridges involved and now am completely confused.

I am trying to bridge three interfaces, two of which are supposed to act as trunk (hdlc0 and hdlc1) and one is supposed to act as access port (eth0). I also need to enable RSTP on each interface included in bridge, but with the configuration listed below RSTP packets are sent via hdlc0 and hdlc1 tagged (!) so other devices rejects them. As Linux has no concept of 'native vlan', I have no idea how to fix it.

Here's my configuration:

ifconfig eth0 up


ifconfig hdlc0 up
ifconfig hdlc1 up

vconfig add hdlc0 42
vconfig add hdlc1 42
ifconfig hdlc0.42 up
ifconfig hdlc1.42 up


brctl addbr br1
brctl addif br1 eth0
brctl addif br1 hdlc0.42
brctl addif br1 hdlc1.42

ifconfig br1 up
brctl stp br1 on

Another question: I also wonder how to configure RSTP in scenarios where I have multiple bridges: say eth0 is trunk with vlan 42-42 allowed, vlan 42 is supposed to pass via hdlc0 and vlan 43 is supposed to go via hdlc1, so I have two bridges. If i enable RSTP on both bridges it will (probably) run independently on each bridge so I'll face problems soon?

已采纳解答

原帖链接 · Paul Donohue · CC BY-SA 3.0

In Linux, VLANs and bridges are completely separate constructs, and Linux bridges are are not "VLAN aware".

When you create a VLAN interface, Linux tags/untags packets on that interface before passing them to/from the underlying physical ("trunk") interface. However, you can still use the underlying physical interface to send untagged ("native VLAN") packets.

When you create a bridge, Linux switches packets between the associated interfaces without any concern for the VLAN tags (or lack thereof) on the packets. If you attach a trunk interface to a bridge, the bridge will happily switch VLAN tagged packets with no regard for the tags. When you enable STP on a bridge, Linux generates untagged STP packets and drops them on the bridge.

When a bridge is attached to a physical interface that also has associated VLAN interfaces, those VLAN interfaces will stop seeing any traffic that is not destined for the MAC address of the physical interface. This behavior is due to the order in which bridging and VLAN tagging are processed, and can be altered using ebtables as described at http://blog.rackspace.com/vms-vlans-and-bridges-oh-my-part-2 . However, as far as Spanning Tree is concerned, attaching bridges to both a physical interface and the associated VLAN interfaces will only work properly if you are using PVST+ anyway (because STP port blocking is managed independently for each bridge), so it is not really relevant here.

But you can also create VLAN interfaces on top of a bridge that is passing VLAN tagged packets, and then add those VLAN interfaces to other bridges.

So, to accomplish what you want, try:

ip link set dev hdlc0 up
ip link set dev hdlc1 up

brctl addbr br_native
brctl addif br_native hdlc0
brctl addif br_native hdlc1
brctl stp br_native on
ip link set dev br_native up

ip link add link br_native name br_native.42 type vlan id 42
ip link set dev br_native.42 up
ip link set dev eth0 up

brctl addbr br_42
brctl addif br_42 br_native.42
brctl addif br_42 eth0
ip link set dev br_42 up

Note that the Linux kernel bridging code only natively supports traditional 802.1D STP. To add support for RSTP and PVST+, use https://github.com/mstpd/mstpd (Some relevant documentation for mstpd can also be found on: https://docs.cumulusnetworks.com/display/DOCS/Spanning+Tree+and+Rapid+Spanning+Tree ). mstpd is also capable of speaking MSTP, but due to the way Linux implements its FIBs, it is currently impossible to map MSTP topologies onto Linux bridges, so MSTP is not actually functional.

To answer your second question, I don't believe it is possible (on any switch, not just when using Linux) to use STP or RSTP to direct each of two different VLANs on a single trunk through two other trunks. This can only be accomplished using PVST+ or MSTP, although as mentioned above MSTP is not supported in Linux.

摘自公开归档,保留原文语言,版式经整理,外部媒体与邮箱地址已移除。

资料来源与适用范围

资料来源
Server Fault
适用范围
以原帖系统、软件版本与发布日期为准(2017-01-06)
内容语言
中文;命令、路径和错误标识保留技术原文
本地收录日期
2026-11-15
授权说明
CC BY-SA 3.0

正文与所需资源由本站本地存储。查看来源及更新记录 ↗

请按适用版本和实际日志确认原因;本站没有对每一种系统或设备逐项执行文中的操作。