问题原文
原帖链接 · a coder · CC BY-SA 3.0
Recently installed RHEL7 on a PowerEdge R320 with the following drives:
2 x 300GB sas 15k
2 x 1TB sas 7.2k
When setting up LVM during installation I purposefully left over several hundred GB free in case I needed to expand later.
I'm now seeing that I need to expand one of the volumes created during install.
The problem is pvs is only showing what I created, and is not showing any usable free space.
[user@box ~] pvdisplay
--- Physical volume ---
PV Name /dev/sda2
VG Name rhel_os
PV Size 165.79 GiB / not usable 0
Allocatable yes (but full)
PE Size 4.00 MiB
Total PE 42443
Free PE 0
Allocated PE 42443
PV UUID sDdEfu-qagM-qq35-OGfF-HpPw-Bizd-LcXazt
--- Physical volume ---
PV Name /dev/sdb1
VG Name rhel_data
PV Size 139.71 GiB / not usable 4.00 MiB
Allocatable yes
PE Size 4.00 MiB
Total PE 35766
Free PE 1
Allocated PE 35765
PV UUID Jgjcad-idBE-wxXc-tGGf-SY8m-qb8T-nBi9ar
parted shows the free space:
[user@box ~]# parted
GNU Parted 3.1
Using /dev/sda
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) print free
Model: DELL PERC H710 (scsi)
Disk /dev/sda: 299GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:
Number Start End Size Type File system Flags
18.4kB 1049kB 1030kB Free Space
1 1049kB 301MB 300MB primary xfs boot
2 301MB 178GB 178GB primary lvm
178GB 299GB 121GB Free Space
and /dev/sdb:
[user@box ~]# parted /dev/sdb
(parted) print free
Model: DELL PERC H710 (scsi)
Disk /dev/sdb: 1000GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:
Number Start End Size Type File system Flags
32.3kB 1049kB 1016kB Free Space
1 1049kB 150GB 150GB primary lvm
150GB 1000GB 850GB Free Space
1) What do I need to do to make use of the free 850GB?
2) In the future, how could I have placed all of the Free Space into the physical volume (thus making it easier to use with LVM)?
已采纳解答
原帖链接 · Law29 · CC BY-SA 3.0
LVM will only show space that has been formatted for LVM by using pvcreate. Here, it doesn't seem you even have a partition.
1) First you need to create the partition (sda3 I suppose), using your favorite partitioning tool. Assign the LVM tag to the partition. Then, assuming that your 121GB partition is /dev/sda3, you need to run pvcreate /dev/sda3 to get it recognized by LVM. After that you will probably want to run either vgextend rhel_os /dev/sda3 or maybe vgextend rhel_data /dev/sda3 (thanks @bodgit)
2) To avoid this happening you should have assigned all space to LVM, but kept your individual LVs small. Usually /home will be very large, just reduce it, and don't worry that the sum of the LVs is smaller than the total. I forget how you'd do that exactly, since it's been decades since I partitioned a RedHat without an automated deployment tool :)
Another solution would be to extend your sda2 partition and tell LVM about it, but that introduces an additional risk of error that is useless in this case.
摘自公开归档,保留原文语言,版式经整理,外部媒体与邮箱地址已移除。
