大网数据广告活动
服务器运维问答

DL580 G7 giving only low performance on CPU (E7 4870)

· 52CE 我爱测

I have a DL580 G7 with four E7 4870 and 128gb of RAM installed (eight cartridges with 2x 8gb each). The operation system is Ubuntu 18.04. There is a TITAN X on the pcie16 and the obligatory p410i installed, but no other periphery…

问题原文

原帖链接 · Sebastian_學生 · CC BY-SA 4.0

I have a DL580 G7 with four E7 4870 and 128gb of RAM installed (eight cartridges with 2x 8gb each). The operation system is Ubuntu 18.04. There is a TITAN X on the pcie16 and the obligatory p410i installed, but no other periphery. When I benchmark this system, I get about 50% of the performance that it should give. For example this is a reference benchmark of a DL580G7 with a slightly weaker CPU (E7 4850) and a otherwise similar setup.

However my system is only able to produce half of the performance in the same benchmark (I get about 980 for the CPU and 20,000 multicore performance). This does not seem to be right.

The benchmark is showing all 80 cores and 128gb of RAM, so the hardware is recognized correctly.

I have already gone through the low latency tuning checklist of HP and changed the BIOS accordingly. The power settings in ILO3 are all on max performance.

Ubuntu is set to the "performance" governor on all 80 cores.
I noticed that even when I put the system under high stress (like crunching numbers on all 80 cores with 100% CPU use for hours) the heat of the CPU's barely changes (they remain at 40 degree) and the fans don't spin up at all (they stay at 40%). The total power consumption displayed in ILO3 goes up to 650 Watts, but I would expect that to be more close to 1KW under stress conditions. I am a bit puzzled by this.

I already tried out different BIOS versions. The original BIOS was a 07/01/2013, which has caused performance issues for other users as well (such reports are found on the internet). So I downgraded it to 12/03/2012 and the problem remains.

Also when I compare the performance of this machine with my previous machine (having an i5 4460) I noticed a drop in single core performance by the factor of four on my applications (on not IO-intensive things like adding large numbers of vectors), which is consistent with the results on the benchmarks, but a drop in single core performance of the factor two would be what I expected. I am only concerned about the CPU performance. AS far as I can see the RAID is doing alright, IO is as expected (but might also suffer due to the diminished CPU performance).

When I do a cat /proc/cpuinfo during stress periods, I see that the CPU's are running at 2,2Ghz.

So far what I didn't yet do is test a different operating system. I am going to do that as soon as I get the opportunity to reboot the machine.

社区高分解答

原帖链接 · ewwhite · CC BY-SA 4.0

I miss seeing questions like this on Server Fault... but at the same time, it's not a common request.

The server is an old architecture. You're making some assumptions that could be leading you down the wrong path.

My recommendations:

You shouldn't only rely on the features recommended in the HP Low-Latency tuning guide. That was meant for specialized applications like algorithmic trading where determinism and predictable resource utilization is the goal. Realtime performance characteristics and low-latency don't necessarily mean faster.

I would look at the CPU's capabilities and work back from there...

Intel Xeon E7-4870
Launched 2011, went end-of-life sometime in 2015.

This is a Turbo Boost-capable CPU. The max turbo frequency is 2.80GHz. When you use a fixed setting like "HP Static High Performance Mode", it actually disables Turbo Boost. In this situation, you'd be better off using the OS Control Mode under your flavor of Linux. (I also recommend this for VMware systems!)

Inside your OS, see if it's possible to install powertop and turbostat.

Monitor one or both during your computational runs.

I'm surprised you're looking at the CPU temperatures or power consumption. I've never used that as a gauge of what the server is doing. What you are missing by using Ubuntu (generally unsupported on HP ProLiant hardware) is the interaction between the OS and the ILO management processor. This is one of the value-adds of ProLiant equipment. With baremetal systems, I try to use a RHEL/CentOS-like OS because of the hardware monitoring and health integration.

Also, go back to the most current BIOS revision. There's rarely a reason to downgrade HP system firmware. Please also ensure your ILO3 firmware is current.

摘自公开归档,保留原文语言,版式经整理,外部媒体与邮箱地址已移除。

资料来源与适用范围

资料来源
Server Fault
适用范围
以原帖系统、软件版本与发布日期为准(2018-09-02)
内容语言
中文;命令、路径和错误标识保留技术原文
本地收录日期
2026-11-15
授权说明
CC BY-SA 4.0

正文与所需资源由本站本地存储。查看来源及更新记录 ↗

请按适用版本和实际日志确认原因;本站没有对每一种系统或设备逐项执行文中的操作。