大网数据广告活动
服务器运维问答

Cisco Catalyst "Traffic Spanning" not working, multiple methods attempted, not sure what to try next

· 52CE 我爱测

So we have an odd setup here. Where I work, we have two Nexus 9k switches running our core network - A and B named respectively, and they have span ports which send traffic to a Catalyst 2960-X which in turn relays to another sys…

问题原文

原帖链接 · Thomas Ward · CC BY-SA 4.0

So we have an odd setup here. Where I work, we have two Nexus 9k switches running our core network - A and B named respectively, and they have span ports which send traffic to a Catalyst 2960-X which in turn relays to another system for traffic monitoring (which only has one NIC unfortunately)

Initially we were using an intermediate VLAN within the Catalyst switch of VLAN 1000 to try and hand off the traffic in a way that'd be properly detected and passed to the traffic monitoring system, such that ports 46, 46, and 47 all had:

switchport mode access
switchport access vlan 1000

... and this was working. However, after moving to a new datacenter, keeping the port connections identical, this no longer works.

We also attempted to do this as a Catalyst-local SPAN port as this diagram shows, after deconfiguring the switchport access modes to go to just straight SPAN behavior:

Neither the VLAN / access port method nor the SPAN methods seem to work to pass traffic to the monitoring system. The interface statistics from show int gig 1/0/45 or show int gig 1/0/46 on the Catalyst show traffic increase and number of packets received as constantly incrementing with the packet counters. But, this no longer relays traffic over the SPAN in the Cataylst to port 48 - its counters show zero packet activity, and the downstream traffic monitoring system sees no traffic coming over this.

Anyone got any idea in how we can make this work again? The traffic monitoring system is a dedicated appliance that only has one uplink port, so we can't go and throw an extra NIC into the equation to pump traffic direct to the traffic monitor from each switch via individual NICs, unfortunately...


Catalyst span config:

monitor session 1 source int gig 1/0/45 both
monitor session 1 source int gig 1/0/46 both
monitor session 1 dest int gig 1/0/48

Nexus local span config (identical for both, note this is not an RSPAN setup):

monitor session 1
    source vlan 20-21,121,150,160,270,300,400,500 both
    destination interface Ethernet1/15
    no shut

Note that we can confirm based on the 'receive' rates on the Catalyst's ports 45 and 46 that traffic is coming from the NEXUS and reaching ports 45 and 46 on the Catalyst, it's just not passing the traffic along to span port 48 on the Catalyst from those two ports.


ALso note that VLAN 1000 does not exist anywhere else on the network, and is at this point not in play; the access switchport configs were deleted in an attempt to use standard SPAN instead, though neither mechanism works. (VLAN 1000 was used as a straight switch-internal-only VLAN to try and trick the system to pass the packets in untagged from from the Nexuses to the port where the monitoring system was in place)


Requested output of show monitor session 1 detail on the Catalyst:

#show monitor session 1 detail
Session 1
---------
Type                     : Local Session
Description            : -
Source Ports             :
    RX Only              : None
    TX Only              : None
    Both                 : Gi1/0/45-46
Source VLANs             :
    RX Only              : None
    TX Only              : None
    Both                 : None
Source RSPAN VLAN      : None
Destination Ports      : Gi1/0/48
    Encapsulation      : Native
          Ingress      : Disabled
Filter VLANs           : None
Dest RSPAN VLAN        : None

Catalyst 2960-X currently running config show run (partly sanitized to hide sensitive information):

Current configuration : 8036 bytes
!
! Last configuration change at 17:13:19 UTC Thu Apr 4 2019 by admin
! NVRAM config last updated at 16:20:59 UTC Mon Apr 1 2019 by admin
!
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname catalyst
!
boot-start-marker
boot-end-marker
!
!
[username data snipped]
aaa new-model
!
!
aaa authentication login default local
aaa authentication enable default none
aaa authorization commands 15 default local
!
!
!
!
!
!
aaa session-id common
switch 1 provision ws-c2960x-48fps-l
!
!
!
!
!
!
!
!
!
crypto pki trustpoint TP-self-signed-2307906176
 enrollment selfsigned
 subject-name cn=IOS-Self-Signed-Certificate-2307906176
 revocation-check none
 rsakeypair TP-self-signed-2307906176
!
!
crypto pki certificate chain TP-self-signed-2307906176
 certificate self-signed 01
  [SNIP]
        quit
spanning-tree mode pvst
spanning-tree extend system-id
!
!
!
!
vlan internal allocation policy ascending
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0
 no ip address
!
interface GigabitEthernet1/0/1
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/2
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/3
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/4
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/5
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/6
 description exagrid mgmt
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/7
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/8
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/9
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/10
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/11
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/12
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/13
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/14
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/15
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/16
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/17
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/18
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/19
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/20
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/21
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/22
 description WAN Switch
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/23
 description Core 9K A
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/24
 description Core 9K B
 switchport access vlan 255
 switchport mode access
!
interface GigabitEthernet1/0/25
 description UPLINK TO MGT NETWORK
 switchport trunk allowed vlan 255
 switchport mode trunk
!
interface GigabitEthernet1/0/26
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/27
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/28
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/29
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/30
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/31
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/32
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/33
 description esx500 console
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/34
 description esx501 Console
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/35
 description esx502 Console
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/36
 description esx503 Console
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/37
 description esx504 Console
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/38
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/39
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/40
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/41
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/42
 switchport access vlan 255
 switchport mode access
 spanning-tree portfast
!
interface GigabitEthernet1/0/43
!
interface GigabitEthernet1/0/44
!
interface GigabitEthernet1/0/45
 description Core A Monitor Port
!
interface GigabitEthernet1/0/46
 description Core B Monitor Port
!
interface GigabitEthernet1/0/47
!
interface GigabitEthernet1/0/48
 description Monitor Ports to Monitoring System
!
interface GigabitEthernet1/0/49
!
interface GigabitEthernet1/0/50
!
interface GigabitEthernet1/0/51
!
interface GigabitEthernet1/0/52
!
interface Vlan1
 no ip address
!
interface Vlan255
 ip address 10.1.255.21 255.255.255.0
!
interface Vlan1000
 description SPAN collection
 no ip address
!
ip http server
ip http secure-server
!
!
!
!
!
!
!
line con 0
line vty 0 4
 timeout login response 300
 transport input telnet ssh
line vty 5 15
 timeout login response 300
 transport input telnet ssh
!
!
monitor session 1 source interface Gi1/0/45 - 46
monitor session 1 destination interface Gi1/0/48
end

已采纳解答

原帖链接 · Ron Maupin · CC BY-SA 4.0

Based on the comments, it seems that you had not created the VLAN in the VLAN database on the switch.

Not creating VLANs with the global vlan command for a stand-alone switch is a common source of problems. Switches that use trunks usually have VTP enabled, and the VLAN database will be populated by VTP. With stand-alone switches, and switches in VTP transparent mode, you need to make sure to create the VLANs used on the switch.

This seems to have solved your problem.

摘自公开归档,保留原文语言,版式经整理,外部媒体与邮箱地址已移除。

资料来源与适用范围

资料来源
Server Fault
适用范围
以原帖系统、软件版本与发布日期为准(2019-04-04)
内容语言
中文;命令、路径和错误标识保留技术原文
本地收录日期
2026-11-15
授权说明
CC BY-SA 4.0

正文与所需资源由本站本地存储。查看来源及更新记录 ↗

请按适用版本和实际日志确认原因;本站没有对每一种系统或设备逐项执行文中的操作。