问题原文
原帖链接 · arturh · CC BY-SA 3.0
I have set up a working Kubernetes cluster using Rancher which defines two networks:
10.42.0.0/16for pod ip addresses10.43.0.0./16for service endpoints
I want to use my existing Caddy reverse proxy to access those service endpoints, so I defined a route (10.10.10.172 is one of my kubernetes nodes):
sudo route add -net 10.43.0.0 netmask 255.255.0.0 gw 10.10.10.172
My routing table on the Caddy web server:
arturh@web:~$ sudo route
[sudo] password for arturh:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default DD-WRT.local 0.0.0.0 UG 0 0 0 eth0
10.10.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
10.43.0.0 rancherkube1.lo 255.255.0.0 UG 0 0 0 eth0
172.17.0.0 0.0.0.0 255.255.0.0 U 0 0 0 docker0
Using this setup I can access and use 10.43.0.1:443 without any issues (it is the main kubernetes api endpoint):
arturh@web:~$ nmap 10.43.0.1 -p 443 | grep 443
443/tcp open https
arturh@web:~$ curl -k https://10.43.0.1
Unauthorized
But accessing any other IP address in the 10.43.0.0/16 network fails and I cannot figure out why:
arturh@web:~$ kubectl get svc | grep prometheus-server
prometheus-prometheus-server 10.43.115.122 <none> 80/TCP 1d
arturh@web:~$ curl 10.43.115.122
curl: (7) Failed to connect to 10.43.115.122 port 80: No route to host
arturh@web:~$ traceroute 10.43.115.122
traceroute to 10.43.115.122 (10.43.115.122), 30 hops max, 60 byte packets
1 rancherkube1.local (10.10.10.172) 0.348 ms 0.341 ms 0.332 ms
2 rancherkube1.local (10.10.10.172) 3060.710 ms !H 3060.722 ms !H 3060.716 ms !H
I can access everything from the kubernetes node itself:
[rancher@rancherkube1 ~]$ wget -qO- 10.43.115.122
<!DOCTYPE html>
<html lang="en">...
which works because of iptable NAT rules:
[rancher@rancherkube1 ~]$ sudo iptables -t nat -L -n | grep 10.43
KUBE-SVC-NGLRF5PTGH2R7LSO tcp -- 0.0.0.0/0 10.43.115.122 /* default/prometheus-prometheus-server:http cluster IP */ tcp dpt:80
KUBE-SVC-NPX46M4PTMTKRN6Y tcp -- 0.0.0.0/0 10.43.0.1 /* default/kubernetes:https cluster IP */ tcp dpt:443
I'm confused because the entries for 10.43.0.1 which works looks identical the the others which do not... I figure I need to add an iptables rule to allow access to the 10.43.0.0/16 subnet, but I'm not familiar with iptables.
I'm quite new to the whole kubernetes business, is this the correct way to go about accessing your service endpoints? If so can someone please help me with the correct iptables command?
已采纳解答
原帖链接 · Mike · CC BY-SA 3.0
you can access things from a host that's running a kubernetes workload because it has the iptables rules and possible route table rules to route traffic.
If you want to access the kubernetes services from outside your cluster then you want to use a ingress controller with a ingress service.
https://kubernetes.io/docs/concepts/services-networking/ingress/
摘自公开归档,保留原文语言,版式经整理,外部媒体与邮箱地址已移除。
