大网数据广告活动
启动与系统组件

Fast startup causes hibernation or shutdown to fail in Windows 10 or Windows 8.1

· 52CE 我爱测

Provides help to solve an issue where the process fails when you try to shut down or hibernate the system on a computer.

This article provides help to solve an issue where the process fails when you try to shut down or hibernate the system on a computer.

Applies to:   Windows 10 - all editions
Original KB number:   3211190

Symptoms

When you try to shut down or hibernate the system on a computer that's running Windows 10 or Windows 8.1, the process fails and reverts to the Windows Lock screen.

Additionally, when you go to the Details tab in this event and then select friendly view, you may notice the following:

Binary data:

In Words

0000: 00000000 00000001 00000000 C004002D
0010: 00002005 C0000034 00000000 00000000
0020: 00000000 00000000

C0000034 - means STATUS_OBJECT_NAME_NOT_FOUND

C004002D - means IO_DUMP_DRIVER_LOAD_FAILURE

Cause

This issue may occur if Fast Startup is enabled under Control Panel\All Control Panel Items\Power Options\System Settings. When Fast Startup is enabled and a user shuts down the computer, all sessions are logged off, and the computer enters hibernation. As part of the hibernation process, Windows initializes the system's memory dump configuration. If the driver is not loaded, it fails to hibernate, and the event that's mentioned in the Symptoms section is logged. This brings you back to the Windows Lock screen.

Resolution

Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see How to back up and restore the registry in Windows.

To resolve this issue, check whether event ID 45 is logged in the System log. If you see this event, verify the contents under the DumpFilters registry value:

  1. Open the Run box. To do this, press the Windows logo key‌ + R.

  2. Type regedit, and then press Enter.

  3. Locate and click the following registry entry:
    HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\CrashControl\

  4. From the pane on the right, verify the contents under the DumpFilters registry value.

  5. Remove everything and make sure that dumpfve.sys is the only value listed.

  6. Exit Registry editor.

  7. Restart the computer to enable Fast Startup.

Workaround

If you want to shut down the computer without using the Hybrid Shutdown behavior, you can use Shutdown.exe instead. Full shutdown is the default when you use Shutdown.exe, as follows:

Shutdown /s /t 0  

The Shutdown.exe command also includes an optional /hybrid parameter that can be used if you want to use the new method:

Shutdown /s /hybrid /t 0 

Note:

  • The Fast Startup setting doesn't apply to Restart.
  • Fast Startup is enabled by default in Windows.
  • Disabling Fast Startup is not recommended.

More information

During Fast Startup, the kernel session is not closed, but it is hibernated. Fast Startup is a setting that helps the computer start faster after shutdown. Windows does this by saving the kernel session and device drivers (system information) to the hibernate (hiberfil.sys) file on disk instead of closing it when you shut down the computer.

When you restart the computer, this typically means that you want a completely new Windows state, either because you have installed a driver or replaced Windows elements that cannot be replaced without a full restart.

Therefore, the restart process in Windows continues to perform a full boot cycle, without the hibernation performance improvement that's described in this article.

Data collection

If you need assistance from Microsoft support, we recommend you collect the information by following the steps mentioned in Gather information by using TSS for deployment-related issues.

Source: Microsoft Learn / IT Pro troubleshooting by Microsoft and contributors. Documentation licensed CC BY 4.0. Code samples are covered by the MIT License. Converted from Markdown, with links normalized and embedded media omitted.

资料来源与适用范围

资料来源
Microsoft Learn / IT Pro troubleshooting
适用范围
- Supported versions of Windows Client · Source date 02/12/2026
内容语言
中文;命令、路径和错误标识保留技术原文
本地收录日期
2026-11-15
授权说明
CC BY 4.0 (documentation), MIT (code samples)

正文与所需资源由本站本地存储。查看来源及更新记录 ↗

请按适用版本和实际日志确认原因;本站没有对每一种系统或设备逐项执行文中的操作。