大网数据广告活动
账户与安全

BitLocker cannot encrypt a drive: known issues

· 52CE 我爱测

Provides guidance for troubleshooting known issues that may prevent BitLocker Drive Encryption from encrypting a drive.

This article describes common issues that prevent BitLocker from encrypting a drive. This article also provides guidance to address these issues.

Note: If it is determined that the BitLocker issue involves the trusted platform module (TPM), see BitLocker cannot encrypt a drive: known TPM issues.

Error 0x80310059: BitLocker drive encryption is already performing an operation on this drive

When BitLocker Drive Encryption is turned on a computer that is running Windows 10 Professional or Windows 11, the following message may appear:

ERROR: An error occurred (code 0x80310059): BitLocker Drive Encryption is already performing an operation on this drive. Please complete all operations before continuing. NOTE: If the -on switch has failed to add key protectors or start encryption, you may need to call manage-bde -off before attempting -on again.

Cause of Error 0x80310059

This issue may be caused by settings that are controlled by group policy objects (GPOs).

Resolution for Error 0x80310059

Important: Follow the steps in this section carefully. Serious problems might occur if the registry is modified incorrectly. Before modifying the registry, back up the registry for restoration in case problems occur.

To resolve this issue, follow these steps:

  1. Start Registry Editor, and navigate to the following subkey:

    HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\FVE

  2. Delete the following entries:

    • OSPlatformValidation_BIOS
    • OSPlatformValidation_UEFI
    • PlatformValidation
  3. Exit registry editor, and turn on BitLocker drive encryption again.

<!--

REMOVING THIS SECTION SINCE IT ONLY APPLIES TO WINDOWS 10 VERSIONS THAT BEEN OUT OF SUPPORT FOR SEVERAL YEARS

Access is denied message when attempting to encrypt removable drives

A computer is running Windows 10, version 1709 or version 1607. Encryption is attempted on a USB drive by following these steps:

  1. In Windows Explorer, right-click the USB drive and select Turn on BitLocker.

  2. On the Choose how you want to unlock this drive page, select Use a password to unlock the drive.

  3. Follow the instructions on the page to enter a password.

  4. On the Are you ready to encrypt this drive? page, select Start encrypting.

  5. The Starting encryption page displays the message Access is denied.

The message is received on any computer that runs Windows 10 version 1709 or version 1607, when any USB drive is used.

Cause of Access is denied message

The security descriptor of the BitLocker drive encryption service (BDESvc) has an incorrect entry. Instead of NT AUTHORITY\Authenticated Users, the security descriptor uses NT AUTHORITY\INTERACTIVE.

To verify that this issue has occurred, follow these steps:

  1. On an affected computer, open an elevated Command Prompt window and an elevated PowerShell window.

  2. At the command prompt, enter the following command:

    C:\>sc sdshow bdesvc
    

    The output of this command resembles the following output:

    D:(A;;CCDCLCSWRPWPDTLORCWDWO;;;SY)(A;;CCDCLCSWRPWPDTLORCWDWO;;;BA)(A;;CCLCSWRPLORC;;;BU)(A;;CCLCSWRPLORC;;;AU)S:(AU;FA;CCDCLCSWRPWPDTLOSDRCWDWO;;;WD)

  3. Copy this output, and use it as part of the ConvertFrom-SddlString command in the PowerShell window, as follows.

    Screenshot of the output of the ConvertFrom-SddlString command, showing NT AUTHORITY\\INTERACTIVE.

    If NT AUTHORITY\INTERACTIVE is seen as highlighted in the output of this command, this line is the cause of the issue. Under typical conditions, the output should resemble the following output instead:

    Screenshot of the output of the ConvertFrom-SddlString command, showing NT AUTHORITY\\Authenticated Users.

Note: GPOs that change the security descriptors of services have been known to cause this issue.

Resolution for Access is denied message

  1. To repair the security descriptor of BDESvc, open an elevated PowerShell window and enter the following command:

    sc sdset bdesvc D:(A;;CCDCLCSWRPWPDTLORCWDWO;;;SY)(A;;CCDCLCSWRPWPDTLORCWDWO;;;BA)(A;;CCLCSWRPLORC;;;BU)(A;;CCLCSWRPLORC;;;AU)S:(AU;FA;CCDCLCSWRPWPDTLOSDRCWDWO;;;WD)
    
  2. Restart the computer.

The issue should now be resolved.

-->

Source: Microsoft Learn / IT Pro troubleshooting by Microsoft and contributors. Documentation licensed CC BY 4.0. Code samples are covered by the MIT License. Converted from Markdown, with links normalized and embedded media omitted.

资料来源与适用范围

资料来源
Microsoft Learn / IT Pro troubleshooting
适用范围
- Supported versions of Windows Client · Source date 02/12/2026
内容语言
中文;命令、路径和错误标识保留技术原文
本地收录日期
2026-11-15
授权说明
CC BY 4.0 (documentation), MIT (code samples)

正文与所需资源由本站本地存储。查看来源及更新记录 ↗

请按适用版本和实际日志确认原因;本站没有对每一种系统或设备逐项执行文中的操作。