大网数据广告活动
账户与安全

Enable debug logging for Netlogon service

· 52CE 我爱测

Describes how to enable logging of debug information of the Netlogon service.

This article describes the steps to enable logging of the Netlogon service in Windows to monitor or troubleshoot authentication, DC locator, account lockout, or other domain communication-related issues.

Original KB number:   109626

More information

Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:

322756 How to back up and restore the registry in Windows

The version of Netlogon.dll that has tracing included is installed by default on all currently supported versions of Windows. To enable debug logging, set the debug flag that you want by using Nltest.exe, the registry, or Group Policy. To do it, follow these steps:

For Windows Server 2019, Windows Server 2016, Windows Server 2012 R2

Note: These steps also apply to Windows 10.

To enable Netlogon logging:

  1. Open a Command Prompt window (administrative Command Prompt window for Windows Server 2012 R2 and later versions).

  2. Type the following command, and then press Enter:

    Nltest /DBFlag:2080FFFF
    
  3. It's typically unnecessary to stop and restart the Netlogon service for Windows Server 2012 R2 or later to enable Netlogon logging. Netlogon-related activity is logged to %windir%\debug\netlogon.log. Verify new writes to this log to determine whether a restart of the Netlogon service is necessary. If you have to restart the service, open a Command Prompt window (administrative Command Prompt window for Windows 10, and Windows Server 2012 R2 and later versions). Then run the following commands:

    net stop netlogon
    net start netlogon
    

    [!NOTE]

    • In some circumstances, you may have to perform an authentication against the system in order to obtain a new entry in the log to verify that logging is enabled.
    • Using the computer name may cause no new test authentication entry to be logged.

To disable Netlogon logging, follow these steps:

  1. Open a Command Prompt window (administrative Command Prompt window for Windows Server 2012 R2 and higher).

  2. Type the following command, and then press Enter:

     Nltest /DBFlag:0x0
    
  3. It's typically unnecessary to stop and restart the Netlogon service for Windows Server 2012 R2 or later versions to disable Netlogon logging. Netlogon-related activity is logged to %windir%\debug\netlogon.log. Verify that no new information is being written to this log to determine whether a restart of the Netlogon service is necessary. If you have to restart the service, open a Command Prompt window (administrative Command Prompt window for Windows 10, and Windows Server 2012 R2 and later versions). Then run the following commands:

    net stop netlogon
    net start netlogon
    
Alternative methods to enable Netlogon logging
  • In all versions of Windows, you can use the registry method that's provided in the Enable/Disable logging by using registry method section.

  • On computers that are running Windows Server 2012 R2 and later versions of the operating system, you can also use the following policy setting to enable verbose Netlogon logging (value is set in bytes):

    \Computer Configuration\Administrative Templates\System\Net Logon\Specify log file debug output level

Note:

  • A value of decimal 545325055 is equivalent to 0x2080FFFF (which enables verbose Netlogon logging). This Group Policy setting is specified in bytes.

  • The Group Policy method can be used to enable Netlogon logging on a larger number of systems more efficiently. We don't recommend that you enable Netlogon logging in policies that apply to all systems, such as the Default Domain Policy. Instead, consider narrowing the scope to systems that may be causing problems by using one of the following methods:

    • Create a new policy by using this Group Policy setting, and then provide the Read and Apply Group Policy rights to a group that contains only the required computer accounts.
    • Move computer objects into a different OU, and then apply the policy settings at that OU level.
Enable/Disable logging by using registry method

To enable logging, you may have to obtain a checked build of Netlogon.dll.

  1. Start Registry Editor.

  2. If it exists, delete the Reg_SZ value of the following registry entry, create a REG_DWORD value with the same name, and then add the 2080FFFF hexadecimal value:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Netlogon\Parameters\DBFlag

  3. It's typically unnecessary to stop and restart the Netlogon service for Windows Server 2012 R2 and later versions to enable Netlogon logging. Netlogon-related activity is logged to %windir%\debug\netlogon.log. Verify the new writes to this log to determine whether a restart of the Netlogon service is necessary. If you have to restart the service, open a Command Prompt window (administrative Command Prompt window for Windows Server 2012 R2/Windows 10 and above). Then run the following commands:

    net stop netlogon
    net start netlogon
    

Note:

  • In some circumstances, you may have to do an authentication against the system to obtain a new entry in the log to verify that logging is enabled.
  • Using the computer name may cause no new test authentication entry to be logged.

To disable Netlogon logging, follow these steps:

  1. In Registry Editor, change the data value to 0x0 in the following registry key:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Netlogon\Parameters\DBFlag

  2. Exit Registry Editor.

  3. It's typically unnecessary to stop and restart the Netlogon service for Windows Server 2012 R2, Windows 10, or later versions to disable Netlogon logging. Netlogon-related activity is logged to %windir%\debug\netlogon.log. Verify that no new information is being written to this log to determine whether a restart of the Netlogon service is necessary. If you have to restart the service, open a Command Prompt window (administrative Command Prompt window for Windows Server 2012 R2/Windows 10 and later versions of the operating system). Then run the following commands:

    net stop netlogon
    net start netlogon
    

Set the maximum log file size for Netlogon logs:

  • The MaximumLogFileSize registry entry can be used to specify the maximum size of the Netlogon.log file. By default, this registry entry doesn't exist, and the default maximum size of the Netlogon.log file is 20 MB. When the file reaches 20 MB, it's renamed to Netlogon.bak, and a new Netlogon.log file is created. This registry entry has the following parameters:

    • Path: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Netlogon\Parameters
    • Value Name: MaximumLogFileSize
    • Value Type: REG_DWORD
    • Value Data: <maximum log file size in bytes>
  • Remember that the total disk space that's used by Netlogon logging is the size that's specified in the maximum log file size times two (2). It's required to accommodate space for the Netlogon.log and Netlogon.bak file. For example, a setting of 50 MB can require 100 MB of disk space, which provides 50 MB for Netlogon.log and 50 MB for Netlogon.bak.

  • As mentioned earlier, on Windows Server 2012 R2 and later versions of the operating system, you can use the following policy setting to configure the log file size (value is set in bytes):

    \Computer Configuration\Administrative Templates\System\Net Logon\Maximum Log File Size

For more information, click the following article numbers to view the articles in the Microsoft Knowledge Base:
247811 How domain controllers are located in Windows

Source: Microsoft Learn / IT Pro troubleshooting by Microsoft and contributors. Documentation licensed CC BY 4.0. Code samples are covered by the MIT License. Converted from Markdown, with links normalized and embedded media omitted.

资料来源与适用范围

资料来源
Microsoft Learn / IT Pro troubleshooting
适用范围
- Supported versions of Windows Client · Source date 02/12/2026
内容语言
中文;命令、路径和错误标识保留技术原文
本地收录日期
2026-11-15
授权说明
CC BY 4.0 (documentation), MIT (code samples)

正文与所需资源由本站本地存储。查看来源及更新记录 ↗

请按适用版本和实际日志确认原因;本站没有对每一种系统或设备逐项执行文中的操作。