大网数据广告活动
Windows排障命令

comp

· 52CE 我爱测

Reference article for the comp command, which compares the contents of two files or sets of files byte-by-byte.

Compares the contents of two files or sets of files byte-by-byte. These files can be stored on the same drive or on different drives, and in the same directory or in different directories. When this command compares files, it displays their location and file names. If used without parameters, comp prompts you to enter the files to compare.

Syntax

comp [<data1>] [<data2>] [/d] [/a] [/l] [/n=<number>] [/c]

Parameters

Parameter Description
<data1> Specifies the location and name of the first file or set of files that you want to compare. You can use wildcard characters (* and ?) to specify multiple files.
<data2> Specifies the location and name of the second file or set of files that you want to compare. You can use wildcard characters (* and ?) to specify multiple files.
/d Displays differences in decimal format. (The default format is hexadecimal.)
/a Displays differences as characters.
/l Displays the number of the line where a difference occurs, instead of displaying the byte offset.
/n=<number> Compares only the number of lines that are specified for each file, even if the files are different sizes.
/c Performs a comparison that is not case-sensitive.
/off[line] Processes files with the offline attribute set.
/? Displays Help at the command prompt.

Remarks

  • During the comparison, comp displays messages that identify the locations of unequal information between the files. Each message indicates the offset memory address of the unequal bytes and the contents of the bytes (in hexadecimal notation unless the /a or /d command-line parameter is specified). Messages appear in the following format:

    Compare error at OFFSET xxxxxxxx
    file1 = xx
    file2 = xx
    

    After ten unequal comparisons, comp stops comparing the files and displays the following message:

    10 Mismatches - ending compare

  • If you omit necessary components of either data1 or data2, or if you omit data2 entirely, this command prompts you for the missing information.

  • If data1 contains only a drive letter or a directory name with no file name, this command compares all of the files in the specified directory to the file specified in data1.

  • If data2 contains only a drive letter or a directory name, the default file name for data2 becomes the same name as for data1.

  • If the comp command can't find the specified files, it will prompt you with a message about whether you want to compare additional files.

  • The files that you compare can have the same file name, provided they're in different directories or on different drives. You can use wildcard characters (* and ?) to specify file names.

  • You must specify /n to compare files of different sizes. If the file sizes are different and /n isn't specified, the following message is displayed:

    Files are different sizes
    Compare more files (Y/N)?
    

    To compare these files anyway, press N to stop the command. Then, run the comp command again, using the /n option to compare only the first portion of each file.

  • If you use wildcard characters (* and ?) to specify multiple files, comp finds the first file that matches data1 and compares it with the corresponding file in data2, if it exists. The comp command reports the results of the comparison for each file matching data1. When finished, comp displays the following message:

    Compare more files (Y/N)?

    To compare more files, press Y. The comp command prompts you for the locations and names of the new files. To stop the comparisons, press N. When you press Y, you're prompted for which command-line options to use. If you don't specify any command-line options, comp uses the ones you specified before.

Examples

To compare the contents of the directory c:\reports with the backup directory \\sales\backup\april, type:

comp c:\reports \\sales\backup\april

To compare the first ten lines of the text files in the \invoice directory and display the result in decimal format, type:

comp \invoice\*.txt \invoice\backup\*.txt /n=10 /d

Related links

Source: Microsoft Learn / Windows Server documentation by Microsoft and contributors (upstream author metadata: robinharwood). Documentation licensed CC BY 4.0. Code samples are covered by the MIT License. Converted from Markdown, with links normalized and embedded media omitted.

资料来源与适用范围

资料来源
Microsoft Learn / Windows Server documentation
适用范围
Windows Server · Source date 10/16/2017
内容语言
中文;命令、路径和错误标识保留技术原文
本地收录日期
2026-11-15
授权说明
CC BY 4.0 (documentation), MIT (code samples)

正文与所需资源由本站本地存储。查看来源及更新记录 ↗

请按适用版本和实际日志确认原因;本站没有对每一种系统或设备逐项执行文中的操作。